Design and Evaluation of a Reconfigurable Manufacturing System: By the Use of the 2D/3D Computer Simulation

Shuai Zhang, Yang Li, Arne Bilberg, Ronen Hadar

Publikation: Bidrag til bog/antologi/rapport/konference-proceedingKonferencebidrag i proceedingsForskningpeer review

Resumé

In modern manufacturing industry, reconfigurable manufacturing system (RMS) is a promising concept in the research arena. A new RMS system structure has been recently designed by a large consumer goods manufacturer in Europe, aiming to improve its production efficiency. This article shows an exploratory research on the (re)configuration procedure and evaluation of the RMS philosophy based on the new RMS structure, which is part of the RMS research in University of Southern Denmark. Tecnomatix Plant Simulation is used for system analysis and optimization. Results from simulation show that the RMS implemented in this consumer goods manufacturer can be effectively (re)configured as part of the daily operations, and the configuration is analyzed by computer simulation before release. Flexibility can be increased considerably meanwhile the system can maintain an acceptable productivity.
OriginalsprogEngelsk
TitelProceedings of the 7th World Conference on Mass Customization, Personalization, and Co-Creation (MCPC 2014) : Twenty Years of Mass Customization – Towards New Frontiers
RedaktørerThomas D Brunø, Kjeld Nielsen, Kaj A. Jørgensen, Stig B. Taps
Antal sider11
ForlagSpringer
Publikationsdato4. feb. 2014
Sider115-127
ISBN (Trykt)978-3-319-04270-1
ISBN (Elektronisk)978-3-319-04271-8
DOI
StatusUdgivet - 4. feb. 2014
Begivenhed7th World Conference on Mass Customization, Personalization, and Co-Creation - Aalborg, Danmark
Varighed: 4. feb. 20147. feb. 2014
Konferencens nummer: 7

Konference

Konference7th World Conference on Mass Customization, Personalization, and Co-Creation
Nummer7
LandDanmark
ByAalborg
Periode04/02/201407/02/2014
NavnLecture Notes in Production Engineering
ISSN2194-0525

Emneord

  • RMS design
  • performance evaluation
  • Plant simulation
  • modular manufacturing

Citer dette

Zhang, S., Li, Y., Bilberg, A., & Hadar, R. (2014). Design and Evaluation of a Reconfigurable Manufacturing System: By the Use of the 2D/3D Computer Simulation. I T. D. Brunø, K. Nielsen, K. A. Jørgensen, & S. B. Taps (red.), Proceedings of the 7th World Conference on Mass Customization, Personalization, and Co-Creation (MCPC 2014): Twenty Years of Mass Customization – Towards New Frontiers (s. 115-127). Springer. Lecture Notes in Production Engineering https://doi.org/10.1007/978-3-319-04271-8_11
Zhang, Shuai ; Li, Yang ; Bilberg, Arne ; Hadar, Ronen. / Design and Evaluation of a Reconfigurable Manufacturing System : By the Use of the 2D/3D Computer Simulation. Proceedings of the 7th World Conference on Mass Customization, Personalization, and Co-Creation (MCPC 2014): Twenty Years of Mass Customization – Towards New Frontiers. red. / Thomas D Brunø ; Kjeld Nielsen ; Kaj A. Jørgensen ; Stig B. Taps. Springer, 2014. s. 115-127 (Lecture Notes in Production Engineering).
@inproceedings{9d50b1e670ef4b7bbd4ec3079454adf6,
title = "Design and Evaluation of a Reconfigurable Manufacturing System: By the Use of the 2D/3D Computer Simulation",
abstract = "In modern manufacturing industry, reconfigurable manufacturing system (RMS) is a promising concept in the research arena. A new RMS system structure has been recently designed by a large consumer goods manufacturer in Europe, aiming to improve its production efficiency. This article shows an exploratory research on the (re)configuration procedure and evaluation of the RMS philosophy based on the new RMS structure, which is part of the RMS research in University of Southern Denmark. Tecnomatix Plant Simulation is used for system analysis and optimization. Results from simulation show that the RMS implemented in this consumer goods manufacturer can be effectively (re)configured as part of the daily operations, and the configuration is analyzed by computer simulation before release. Flexibility can be increased considerably meanwhile the system can maintain an acceptable productivity.",
keywords = "RMS design, performance evaluation, Plant simulation, modular manufacturing",
author = "Shuai Zhang and Yang Li and Arne Bilberg and Ronen Hadar",
year = "2014",
month = "2",
day = "4",
doi = "10.1007/978-3-319-04271-8_11",
language = "English",
isbn = "978-3-319-04270-1",
series = "Lecture Notes in Production Engineering",
publisher = "Springer",
pages = "115--127",
editor = "Brun{\o}, {Thomas D} and Kjeld Nielsen and J{\o}rgensen, {Kaj A.} and Taps, {Stig B.}",
booktitle = "Proceedings of the 7th World Conference on Mass Customization, Personalization, and Co-Creation (MCPC 2014)",
address = "Germany",

}

Zhang, S, Li, Y, Bilberg, A & Hadar, R 2014, Design and Evaluation of a Reconfigurable Manufacturing System: By the Use of the 2D/3D Computer Simulation. i TD Brunø, K Nielsen, KA Jørgensen & SB Taps (red), Proceedings of the 7th World Conference on Mass Customization, Personalization, and Co-Creation (MCPC 2014): Twenty Years of Mass Customization – Towards New Frontiers. Springer, Lecture Notes in Production Engineering, s. 115-127, 7th World Conference on Mass Customization, Personalization, and Co-Creation, Aalborg, Danmark, 04/02/2014. https://doi.org/10.1007/978-3-319-04271-8_11

Design and Evaluation of a Reconfigurable Manufacturing System : By the Use of the 2D/3D Computer Simulation. / Zhang, Shuai; Li, Yang; Bilberg, Arne; Hadar, Ronen.

Proceedings of the 7th World Conference on Mass Customization, Personalization, and Co-Creation (MCPC 2014): Twenty Years of Mass Customization – Towards New Frontiers. red. / Thomas D Brunø; Kjeld Nielsen; Kaj A. Jørgensen; Stig B. Taps. Springer, 2014. s. 115-127 (Lecture Notes in Production Engineering).

Publikation: Bidrag til bog/antologi/rapport/konference-proceedingKonferencebidrag i proceedingsForskningpeer review

TY - GEN

T1 - Design and Evaluation of a Reconfigurable Manufacturing System

T2 - By the Use of the 2D/3D Computer Simulation

AU - Zhang, Shuai

AU - Li, Yang

AU - Bilberg, Arne

AU - Hadar, Ronen

PY - 2014/2/4

Y1 - 2014/2/4

N2 - In modern manufacturing industry, reconfigurable manufacturing system (RMS) is a promising concept in the research arena. A new RMS system structure has been recently designed by a large consumer goods manufacturer in Europe, aiming to improve its production efficiency. This article shows an exploratory research on the (re)configuration procedure and evaluation of the RMS philosophy based on the new RMS structure, which is part of the RMS research in University of Southern Denmark. Tecnomatix Plant Simulation is used for system analysis and optimization. Results from simulation show that the RMS implemented in this consumer goods manufacturer can be effectively (re)configured as part of the daily operations, and the configuration is analyzed by computer simulation before release. Flexibility can be increased considerably meanwhile the system can maintain an acceptable productivity.

AB - In modern manufacturing industry, reconfigurable manufacturing system (RMS) is a promising concept in the research arena. A new RMS system structure has been recently designed by a large consumer goods manufacturer in Europe, aiming to improve its production efficiency. This article shows an exploratory research on the (re)configuration procedure and evaluation of the RMS philosophy based on the new RMS structure, which is part of the RMS research in University of Southern Denmark. Tecnomatix Plant Simulation is used for system analysis and optimization. Results from simulation show that the RMS implemented in this consumer goods manufacturer can be effectively (re)configured as part of the daily operations, and the configuration is analyzed by computer simulation before release. Flexibility can be increased considerably meanwhile the system can maintain an acceptable productivity.

KW - RMS design

KW - performance evaluation

KW - Plant simulation

KW - modular manufacturing

U2 - 10.1007/978-3-319-04271-8_11

DO - 10.1007/978-3-319-04271-8_11

M3 - Article in proceedings

SN - 978-3-319-04270-1

T3 - Lecture Notes in Production Engineering

SP - 115

EP - 127

BT - Proceedings of the 7th World Conference on Mass Customization, Personalization, and Co-Creation (MCPC 2014)

A2 - Brunø, Thomas D

A2 - Nielsen, Kjeld

A2 - Jørgensen, Kaj A.

A2 - Taps, Stig B.

PB - Springer

ER -

Zhang S, Li Y, Bilberg A, Hadar R. Design and Evaluation of a Reconfigurable Manufacturing System: By the Use of the 2D/3D Computer Simulation. I Brunø TD, Nielsen K, Jørgensen KA, Taps SB, red., Proceedings of the 7th World Conference on Mass Customization, Personalization, and Co-Creation (MCPC 2014): Twenty Years of Mass Customization – Towards New Frontiers. Springer. 2014. s. 115-127. (Lecture Notes in Production Engineering). https://doi.org/10.1007/978-3-319-04271-8_11